Soft plaster surface — routine care keeps the finish alive for decades

Finish Care Guide

Venetian Plaster

Lime-Plaster Care

Care & Maintenance

Keeping Your Venetian Plaster Pristine

A penetrating sealer applied at handover protects the finish for years; a re-seal assessment every 5–7 years keeps high-traffic walls in showroom condition. Dust monthly with a soft, dry cloth, following the direction of the trowel polish to maintain the burnished sheen. Clean only with a soft damp cloth. We do not recommend abrasive cleaners, harsh chemicals, or solvent-based products — the sealer will cloud and the polish will dull.

Before Application

Substrate Preparation

  • Surface must be finished to at least Level 4 drywall — any lower will telegraph texture through the translucent lime layers.
  • Substrate moisture content must not exceed 12% before application begins; use a pin meter and allow newly plastered or concreted walls adequate cure time.
  • Do not apply an acrylic primer on the final coat face — a lime-compatible skim coat or a diluted mineral primer is required to maintain breathability and adhesion.
  • Fill any hairline cracks or surface voids with a pH-neutral skim coat and allow full cure before the base layer is applied.

Routine Care

Three Essential Maintenance Steps

1

Monthly Dry Dusting

Use a soft, lint-free microfiber cloth and follow the direction of the trowel polish. Work in one direction to preserve the burnished surface sheen; cross-hatching over time will dull the polish.

2

Biannual Damp Wipe

Twice a year — or immediately after any water or grease contact — wipe gently with a barely damp cloth using distilled water only. Blot do not rub; excess moisture left on the surface can temporarily whiten the sealer.

3

Annual Sealer Inspection

Check the finish annually for any loss of sheen, chalking, or areas that feel rough or porous. Early sealer failure is localised and simple to re-treat; ignored, it leads to staining that requires a full re-burnish.

Protective Sealing

When to Reseal

A penetrating mineral sealer is applied by the studio at project handover as standard. For residential feature walls under normal use, a re-seal assessment is warranted every 5–7 years. High-traffic walls — entry halls, hospitality environments, or any surface subject to regular contact — should be assessed every 3–4 years. Contact the studio before attempting any DIY top-coat: the wrong product class (acrylic, solvent-based, or wax-over-sealer combinations) can cause delamination or permanent clouding that requires partial or full re-application.

Cleaning Products

What to Use — and What to Avoid

Venetian plaster tolerates gentle cleaning. The sealer is the critical protective layer — anything that degrades it exposes the lime body to staining.

  • Distilled water (preferred over tap water, which can leave mineral deposits)
  • pH-neutral liquid soap with a pH at or below 7.5 — one drop per 500 ml of water, fully diluted
  • Bleach or chlorine-based cleaners — they will strip and discolour the sealer
  • Abrasive sponges, scourers, or scrub pads — they scratch the burnished surface
  • Solvent-based or spirit cleaners — they dissolve the sealer layer
  • Steam cleaners — concentrated heat and moisture penetrate the lime body and cause whitening or delamination

Long-Term Care

Repair & Reapplication

Tinted spot repairs — small nicks, minor scuffs, or isolated sealer loss — are handled in situ by the studio. We keep the original pigment mix and burnish notes for every installation, so colour-matched repairs are typically indistinguishable from the surrounding field. A full-wall re-burnish is warranted at 15–20 years under normal residential use, or earlier if the finish has been exposed to prolonged moisture, heavy UV, or repeated mechanical impact. Please contact the studio before commissioning any third-party refinishing: mismatched lime grades or incorrect sealer products applied over our work can create irreversible adhesion failures that require complete strip-back.

Ready to commission a new Venetian plaster installation?

Book a Consultation ← Back to all finish care guides